Technical Info & Warranty is continued from previous page.
I MAGINE WHAT'S POSSIBLE
2 0 1 6 N E W P R O D U C T C ATA LO G
To assist in deciding whether a specific stone is appropriate for certain uses,
the coding system below was developed and corresponds with the charts on the
following pages for all available natural stone.
Not recommended in wet areas.
Can be used in interior wet wall areas, if sealed and maintained properly. If not
properly maintained, the stone look could be altered. Please contact your sealer
manufacturer or your Daltile sales representative for information about products that
can protect the stone from moisture exposure.
Might contain dry seams, pits, fossils and glass veins that are filled at the factory or
during installation. These are all inherent characteristics of the stone. Since these
voids can sometimes lose their fillings, they should be refilled as part of normal
A sealer is recommended. (Note: Some stones, such as limestone and tumbled stone
among others, should be sealed prior to grouting.)
These stones contain deposits of minerals and iron that may react to moisture. Stone
bleeding or rusting is a common example of this. These stones should not be used
in installations where they would be exposed to standing, run-off water or too much
humidity. A sealer is strongly recommended but will not prevent the chemical reaction
from happening. Contact your sealer manufacturer or Daltile sales representative for
information about products that can protect the stone from moisture exposure.
White setting materials are recommended.
Install with a non-staining epoxy. Do not use any water-based setting material with
Not recommended for shower floors.
Medium bed mortar is required for tiles with at least one side greater than 15".
These stones may change color over time if exposed to direct sunlight.
Use a temporary water soluble grout release during installation.
The existence and dimensions of a bevel may vary from lot to lot. Be sure to request a sample of the
specific lot you are planning to order, if the bevel is an important feature for your job.
Background color is relatively uniform.
Background color contains slight variations.
Background color contains distinct variations.
Variegated in color and veining. Blending allowances during
installation are strongly recommended.
CONDITIONS OF PURCHASE
Natural stone products inherently lack uniformity and are subject to variation in aesthetics (color, shade, finish,
etc.) and performance (hardness, strength, slip resistance, etc.). Natural stone products do not meet minimum
coefficient of friction thresholds recommended by safety standard setting organizations. No warranties, ex-
pressed or implied, relative to merchantability or fitness for a particular purpose are made regarding the natural
stone products distributed by Daltile. Check local building codes prior to specification or installation to verify that
product technical characteristics comply with required parameters.
Suitable for exterior application in freezing and non-freezing climates.
exterior floors in freezing and non-freezing climates.
exterior walls in freezing and non-freezing climates.
exterior countertops in freezing and non-freezing climates.
* exterior floors in non-freezing climates only.
* exterior walls in non-freezing climates only.
Not recommended for exterior applications.
implies an area protected from the elements.
Natural stone products are not recommended for any wet areas where they may
be exposed to chemicals such as waterlines and pools, or to extreme humidity and
heat, such as steam rooms, among others.
not recommended for floor use.
Suitable for residential use. Not recommended for commercial areas.
2 Medium/Light Commercial:
Suitable for light commercial and residential use.
3 Heavy Commercial:
Suitable for most commercial and/or high traffic areas.
Polished surfaces are not recommended for floor areas where slip resistance is a concern. Our
durability recommendations are only based on the technical characteristics of the stones, however, slip
resistance shall still be taken into consideration when selecting the product for a specific application.
Natural stone products do not meet minimum coefficient of friction thresholds recommended by safety
standard setting organizations.
Sound stones with no geological voids or fissures. These stones
do not require any filling or patching.
Similar to Group A, but geological imperfections could be evident.
These stones may contain holes or voids, which are filled with epoxy or resin.
These stones may contain holes, voids, lines of separation and
structural flaws. It is standard practice to repair these stones by filling them
or reinforcing them.
Similar to Group C but these stones contain larger natural faults
and require more refinishing over time.
Soundness is meant to help classify denser stones (Group A and B) from more
fragile stones (Group C and D). Stones classified under Groups C and D may require
additional fabrication before, during or after installation as part of regular maintenance.
STONE USAGE GUIDE
Previous Page - Next Page
-2016 New Product Catalog
Choose a different catalog.
Virtual Catalogs | Daltile